NodeMCU Motor Driver Shield can be used to run 2 DC Motors simultaneously and also acts as an expansion board for NodeMCU Devkit 1.0.

This shield board is driven by the large power full-bridge chip L293DD, which can directly drive 2-channels DC motors or one-channel stepper motor. The current can be up to 1.2A.

The shield board has four ports which are used as PWMA(motor A), PWMB (motor B), DA (direction of motor A), and DB (direction of motor B), respectively.

In addition, this shield board has many pins, such as VIN, 3.3V, DIO, AIO, SDIO, UART, SPI, RST, and EN, thus can conveniently connect all kinds of sensors (e.g., temperature and humidy, buzzer, light, relay sensor, etc.). The board is developed by the humanized design with a power switch, and thus user can control the on-off of power conveniently.This motor shield board can be used to control directly the smart car.

Features:
Motor power (VM): 4.5~36V, can be powered separately
Control power (VIN): 4.5V~9V(10V MAX), can be powered separately
Logic working current (Iss) 60mA
Driven working current (Io): 1.2A
Control signal input voltage: High (above 2.3V), Low(between 0.3 and 1.5V)
Ports: D1, D3 (Motor A); D2, D4 (Motor B)

Write a review

Note: HTML is not translated!
    Bad           Good

NodeMCU Motor Driver Shield

  • INR 210.00


Related Products

SG90 Micro Servo

SG90 Micro Servo

This servo motor is highly suitable for building Pan-Tilt assembly, Robot-Hand control and other sim..

INR 500.00

200RPM Central Shaft

200RPM Central Shaft

Ideal for most mobile robot projects, this motor operates in 6-12V range. Comes soldered with wir..

INR 129.75

BO Single Shaft Straight

BO Single Shaft Straight

Great for many low voltage mobile robot projects, this motor and gearbox combination operates in 3-6..

INR 68.50

MG90 Micro Servo

MG90 Micro Servo

This metal gear servo is most used in camera pan-tilt assembly which requires higher torque than the..

INR 950.00

300RPM Central Shaft

300RPM Central Shaft

Ideal for most mobile robot projects, this motor operates in 6-12V range. Comes soldered with wir..

INR 129.75

BO Single Shaft L-Shaped

BO Single Shaft L-Shaped

Great for many low voltage mobile robot projects, this motor and gearbox combination operates ideall..

INR 68.50

300RPM Johnson Geared Side Shaft

300RPM Johnson Geared Side Shaft

Ideal for off road mobile robots with higher torque requirements. This motor operates in 9-12V range..

INR 385.00

SG90 Micro Servo - Clone

SG90 Micro Servo - Clone

SG90 servo motor is highly suitable for building Pan-Tilt assembly, Robot-Hand control and other sim..

INR 160.00

MG90S Micro Servo - Clone

MG90S Micro Servo - Clone

This metal gear servo is most used in camera pan-tilt assembly which requires higher torque than the..

INR 330.00

NodeMCU Devkit 1.0

NodeMCU Devkit 1.0

NodeMCU Devkit 1.0 is the 5th design of NodeMCU. It uses CP2102 as UART bridge, and can flash firmwa..

INR 470.00

Relay Module - 1 Channel

Relay Module - 1 Channel

This module has a single relay to help you control the appliances around your house. Highly useful i..

INR 80.00

Tags: node, nodemcu, devkit, 1.0, CP2102, motor, driver