• Magician Robot Controller

Magician = Arduino UNO + 0.8A Motor Driver + Servo Shield + Sensor Shield

The Magician' Dual 0.8A Robot Controller is an Arduino compatible controller that uses the ATmega8 processor and comes preloaded with the Arduino boot loader. The USB interface allows the controller to be easily programmed with the Arduino IDE and a Mini-B USB cable. It is designed to work with battery voltages from 6V to 9V. Voltages over 9V will prevent the motor control circuit from functioning correctly. Voltages less than 5.5V can cause the 5V regulator to become unreliable. A reverse polarity protection diode will protect your controller if the power is accidentally reversed. Analog pins A0 - A5 can also be selected as digital pins D14 - D19 allowing them to be used as digital I/O pins. This is an original DAGU product.

This board can be used for mobile robots that have pan-tilt mechanisms, grippers and arms, and numerous sensors mounted on them.

Features:
ATmega8 (can be upgraded to ATmega168 or ATmega328) microcontroller with 16MHz ceramic resonator
USB interface and ISP socket for easy programming
Dual H-bridge motor controller for rated at 800mA for each motor
8X 3-pin servo compatible outputs
Servo power selectable between +5V regulated or battery direct
6X analog inputs with +5V and GND connections to power sensors
Male and female I/O headers for easy connection
Comes pre-tested and pre-loaded with the Arduino IDE.

Does not include Mini-B USB cable

Links:
Product Wiki

Write a review

Note: HTML is not translated!
    Bad           Good

Magician Robot Controller

  • INR 2,700.00
  • INR 1,990.00


Related Products

Mini-B USB Cable

Mini-B USB Cable

This 80cm cable is used with many Arduino and compatible boards for power and sketch uploading purpo..

INR 45.00

ATmega328P-PU

ATmega328P-PU

ATmega328P-PU microcontroller is used in Arduino Uno, and can be used to create an Arduino circuit o..

INR 170.00

ATtiny85-20PU

ATtiny85-20PU

The ATtiny85-20PU is a great microcontroller, for reducing the size of the breadboard circuit, when ..

INR 129.99

Rover 5 Chassis without Encoders

Rover 5 Chassis without Encoders

Rover 5 is a new breed of tracked robot chassis designed by DAGU, specifically for students and hobb..

INR 6,500.00

Multi Chassis Tank Rescuer

Multi Chassis Tank Rescuer

The Multi Chassis Tank Rescuer is perfect for climbing footsteps of upto 15cm height and traversing ..

INR 30,100.00

Multi Chassis 4WD ATV

Multi Chassis 4WD ATV

The 4 wheel drive ATV chassis is perfect for building robots that can handle surfaces such as sand, ..

INR 11,000.00

Multi Chassis Tank Standard

Multi Chassis Tank Standard

The Standard chassis is able to run over a variety of terrains. Features: Max load: 7.5kg Requi..

INR 11,050.00

Multi Chassis 4WD Basic

Multi Chassis 4WD Basic

This 4 wheel drive chassis is a great option for all mobile robots and can run on ceramic tiles, and..

INR 8,999.00

Micro Magician Robot Controller

Micro Magician Robot Controller

Micro Magician = LilyPad + Accelerometer + 1A Motor Driver + Servo Shield + Sensor Shield + Bluetoot..

INR 4,950.00

Simple Encoder (Pair)

Simple Encoder (Pair)

A simple encoder consists of a neodymium 8-pole magnet with rubber hub and a hall-effect sensor term..

INR 2,200.00

Quadrature Encoder (Pair)

Quadrature Encoder (Pair)

This magnetic sensor fits near the back wheel and allows you to measure speed and distance travelled..

INR 1,520.00

Rover 5 Chassis with 2 Encoders

Rover 5 Chassis with 2 Encoders

Rover 5 is a new breed of tracked robot chassis designed by DAGU, specifically for students and hobb..

INR 8,000.00

Rover 5 Chassis with 4 Encoders

Rover 5 Chassis with 4 Encoders

Rover 5 is a new breed of tracked robot chassis designed by DAGU, specifically for students and hobb..

INR 11,000.00

Tags: Arduino, Motor Driver, Motor Shield, Servo Shield, Motor, Servo, Sensor, Shield magician, robot, controller

Discounted Products

FlashForge Creator Pro

FlashForge Creator Pro

Rated in the Top 2 3D Printers of 2015, FlashForge Creator Pro is built for beginners and profession..

INR 90,900.00 INR 112,300.00

FlashForge Dreamer

FlashForge Dreamer

Rated in the Top 2 3D Printers of 2015, FlashForge is built for beginners and professionals alike.Dr..

INR 109,900.00 INR 135,000.00

FlashForge Finder

FlashForge Finder

Rated in the Top 2 3D Printers of 2015, and one of the best 3D Printers for Plug-and-Play FlashForge..

INR 49,900.00 INR 64,999.00

FlashForge Guider II

FlashForge Guider II

Guider II is an industrial grade 3D printer designed for the extreme hobbyist or pro user in mind. T..

INR 173,000.00 INR 199,900.00

FlashForge Hunter

FlashForge Hunter

The best DLP 3D Printer on the market! Flashforge Hunter is an advanced digital light processing (DL..

INR 359,900.00 INR 397,000.00

FlashForge Inventor

FlashForge Inventor

Inventor is a filament-based 3D printer with a totally-enclosed design that is safe to use indoors a..

INR 108,900.00 INR 124,900.00

FlashForge Inventor II

FlashForge Inventor II

Inventor II is the newest filament-based 3D printer designed for children and complete beginners who..

INR 59,200.00 INR 66,990.00

Magician Robot Controller

Magician Robot Controller

Magician = Arduino UNO + 0.8A Motor Driver + Servo Shield + Sensor Shield The Magician' Dual 0.8A..

INR 1,990.00 INR 2,700.00

Mini Driver Robot Controller

Mini Driver Robot Controller

Mini Driver = Arduino NG + 2A Motor Driver + Servo Shield + Sensor Shield + Bluetooth Shield + ISP P..

INR 1,600.00 INR 2,999.00

Robotic Claw

Robotic Claw

This fun robotic claw is ideal for those who love all things robotic! Simple instructions and suppli..

INR 750.00 INR 1,200.00

Spider Robot Controller

Spider Robot Controller

Spider = Arduino Mega + Servo Shield + Servo Expansion Shield This programmable controller from D..

INR 6,200.00 INR 10,499.00

Worbla Black Art - 150x100cm

Worbla Black Art - 150x100cm

The thermoplastic modelling material!Worbla BlackArt shapes, heats, sticks and works just like Worbl..

INR 4,299.00 INR 5,400.00